"The World's Most Economical Solar Pump"
- Lift from as deep as 165 ft (50 m)
- Maximum 3,785 gallons per day (10 m3)
- Eliminates the costs of fuel, delivery, enginemaintenance, and pollution.
- In many cases it COSTS LESS than a conventional pump and generator installation
- Great reliability and life expectancy
- Helical Rotor wet end, brushless motor(maintenance free)
- High resistance to sand and corrosion
- Fits 4" and larger well casings
- Wide voltage range for 24 to 48V systems (2-4 solar modules in series). Only one controller for solar direct or battery systems.
HIGH EFFICIENCY = LOWER COST
PS200 Mini pumps more water per watt than other solar pumps and KEEPS IT UP year after year.
RELIABLE AND MAINTENANCE-FREE
Eliminates the weakest links in solar pumping by using a helical rotor (progressing cavity) pump and a brushless, water-filled motor. No failure-prone diaphragms, no flooded-motor failures.
JUST SAY NO!
- NO to annual diaphragm replacement
- NO to motor brush replacement
- NO to delicate plugs that fail
- NO to pistons, cams, flapper valves
- NO to plastic parts
- NO to electronics in the well
DIRECT REPLACEMENT for SOLAR DIAPHRAGM PUMPS
The PS200 Mini can replace less reliable diaphragm pumps, to eliminate frequent repairs and to increase water production. In most cases, you can use the existing solar array. Refer to the performance table, and compare the solar (minimum PV watts) requirement with the existing equipment.
A PS200 Mini Pump System Iincludes:
- Pump
- Pump controller
- Complete illustrated instruction manual
OPTIONS:
- Submersible cable splice kit
- Low-water probe
DEEP WELL APPLICATIONS
The PS200 Mini can be submersed as deep as necessary. Submersion depth does not affect the performance or place additional stress on the pump or motor.
SURFACE WATER APPLICATIONS
Can be installed in a stream, pond, tank or shallow well, in any position.
DRY RUN PROTECTION
A low water probe (included) turns pump off to prevent dry-run damage. Reset is automatic after 20 minutes. The PS200 Controller has an RPM limit adjustment to reduce the maximum flow rate to about 50%, to help match a limited water source.
SAND AND SILT TOLERANCE
The PS200 Mini has high resistance to wear from sand, clay, etc. that may occur in a properly constructed water well. However, a concentration of solids greater than 2% (by volume) may cause blockage in the pump or the drop pipe, especially at low flow rates. Do not use Mini to clean out a dirty well.
CONTROLLER DISPLAY
Lights indicate: system on, pump on, tank full, water source low, overload, and battery low.
STORAGE REQUIREMENT
A storage tank (not included) should be sized to supply a minimum of 5-10 days water supply, depending on climate and application. Water storage is generally more economical than energy storage in batteries.
BATTERY SYSTEMS
LOW-VOLTAGE DISCONNECT prevents battery damage from overdischarge. This feature is included in the controller.Disconnect - Reconnect 22V�26V and 44V-48V
DROP PIPE
Pump has 1" NPT outlet. If water is dirty, consider a smaller size drop pipe to increase the flow velocity. This helps exhaust solid particles and prevent accumulation in the pipe. When considering reduced pipe size, consult a pipesizing (friction loss) chart. Pipe can be of any standard material, rigid or flexible. A torque arrestor is NOT required.
PUMP CABLE and SPLICE
The pump requires standard submersible cable, 3-wire + ground (total 4 wires). Connection to the pump is made using industry-standard splicing methods.
DIMENSIONS & WEIGHTS
- Controller: 10" x 7" x 4" (260 x 175 x 100 mm)
- 3 conduit holes: 1/2", 3/4", and 1 1/4" KO
- Weight: 3.6 lbs (1.5 kg)
- Enclosure: gasket-sealed, weatherproof
WETTED MATERIALS
316 stainless steel, chromium, NBR rubber, natural rubber, POM, polyurethane (cable)
TEMPERATURE LIMITS
- Pump: water temp. 57 F to 82 F (13 C to 28 C) Other ranges are available by special request.
- Controller: Ambient -22 F to 131 (-30 C to 55 C)
NEED MORE WATER or GREATER LIFT?
Consider the standard System PS600 or PS1200 instead of the PS200 Mini system. These systems use more power, to pump as high as 760 ft (230m) or to produce a maximum of 34,000 gallons per day (120 m3). They are also appropriate for pressurizing applications.
INSTALLATION
Install the pump by the same methods and materials used for conventional submersible pumps. The solararray requires nuts-and-bolts assembly and standard wiring practice. The PS200 Mini instruction manual isclearly illustrated. No special product training is required.
WARRANTY
TWO YEAR manufacturer's warranty against defects in materials and workmanship.
|
