UniRac Rapidrac Ballast Pan with Module Mount
Please call to order.
Have the manufacturer, model number, configuration and number of PV modules ready. Every PV module has a different UniRac Frame Bay part number, but the same cost.
RapidRacG10
UniRac's new improved Rapidrac is the best commercial flat-roof solution for the PV Mounting Industry.
Unirac’s new improved Rapidrac is the best commercial flat-roof solution for the PV Mounting industry.
With minimal parts, reduced labor expenses and the versatility to accommodate a wide range of modules, Rapidrac is one of the fastest, easiest and most cost-effective solutions on the market today.
Accompanied by a technical support system that provides complete installation and code compliance documentation, and design assistance, Unirac continues to deliver value-engineered technology, designed with experienced customer input, to deliver industry-leading mounting solutions.
Rapidrac Time Trial
In a recent time trial, a three-man crew using hand tools installed 3kW of Rapidrac in 1 hour, or 1kW per man hour. The electrical contractor crew had never installed Rapidrac before and had only 30 minutes to review the installation manual.
Key Benefits
Speed of Installation
- Significantly reduce installation time
- Installs in less than half the time of competitive products
- Installation guide is only 4 pages
Simplicity
- Requires only 7 parts to install
- Only 1 wrench required
- No unnecessary complexity
- Advanced engineered
Versatility and Choice
- Offers freedom and flexibility to accommodate majority of PV modules
- Flexibility of design to meet all weight, height and wide range of wind conditions
- Offers trade-off versatility between penetrations and roof load
- Can be installed as light as 2lb/ft2 with many penetrations, or may be installed with zero penetrations (with higher roof loading)
Value
- Price per watt is competitively priced
- Estimated labor savings of up to $10k on 250kw project
- Based on average 200W panel and optimum design configuration
Rapidrac G10
The Rapidrac® G10 has an efficient design. Built at a fixed 10 degree tilt angle, this ballast solution optimizes natural convective cooling of the modules and was designed to meet the requirements of current applicable building codes.
Minimal parts, faster installation, reduced labor expenses and versatility: all customer driven demands that helped engineer this unique flat roof solution.
The Rapidrac G10 was developed through significant computational fluid dynamics and wind tunnel engineering. The efficient design, built at a fixed 10 degree tilt angle, optimizes natural convective cooling of the modules and was designed to meet the requirements of current applicable building codes.
UniRac offers an attachment option for the Rapidrac G10, the RapidFoot, which can be used for seismic restraint and for ballast trade off, allowing for a reduction in roof dead load.
The general rules are:
- Rapidrac is currently available only at 10 degrees fixed tilt
- All modules are racked landscape
- East/West dimension = Length of the modules (round up to nearest inch) x number of modules in row
- North/South dimension = [(Module Width (rounded up to nearest inch) + 16") x number of modules in column] + 16” for the extra north ballast pan
- A continuous array (sub-array) is one where all the rows share ballast trays between them.
Grounding and Ballast
- UniRac supplies WEEB 9.5 grounding clips with the Rapidrac components.
- The grounding clips electrically bond all the modules and Rapidrac components in a sub-array.
- Some inspectors require more than one ground lug for each continuous array.
- In the end, run the ground wire through the ground lugs on each sub-array.
- In the North/South direction you must have ballast pan/module/ballast pan/module/ballast pan. …so you add an additional ballast pan on the north of each column
- Additional ballast pans are required where a column stops for a hole in the racking to accommodate an air conditioner or similar obstruction on the roof
- UniRac specifies Solid Cap Concrete Blocks (4" x 8" x 16", 26 lbs) for ballasting the array.
Rapidrac Installation Video
Warranty: 10-year limited product warranty with 5-year limited finish warranty
Shipping Weights: 12 lbs (5.45 kg)
|
